4 Modular Slots Industrial L2+ IEC61850-3 Managed (PoE) Switch

• IEC 61850-3 & IEEE1613 compliance
• High-density 28 x Gigabit Ethernet L2+ managed (PoE at/af) switch
• Support dual power redundancy AC&DC
• Enhanced G.8032 ring protection < 20ms for single ring. Supports auto mode, enhanced mode, train mode and basic mode; Enhanced G.8032 ring covers multicast packets; MSTP 16MSTI /RSTP; support MRP ring
• Support LACP link aggregation, IGMP v3/router port, MLD snooping, DHCP server & DHCP Option82; DHCP Snooping, Port based DHCP distribution, Mac based DHCP server, QoS by VLAN, SSH v2/SSL, HTTPS, INGRESS/EGRESS ACL L2/L3,TACACS+**, QinQ
• Protocol based VLAN ; IPv4 Subnet based VLAN
• Support relay contact & environmental monitoring
• Miss-wiring avoidance & Node failure protection(node failure protection)
• User friendly UI, including auto topology drawing and DDM threshold monitoring with dB values***
• MMS built-in
• Support USB dongle for automatic backup configuration

OVERVIEW

Lantech I(P)GS-5400-2P-PT is a high performance L2 + managed industrial Ethernet switch which provides L2 wire speed and advanced security function for network aggregation and backbone deployment. It delivers ITU G.8032 enhanced ring recovery less than 20ms in single ring while also supports train ring, enhanced mode, multiple VLAN mode with easy configuration. The comprehensive QoS, QoS by VLAN, advanced security including INGRESS/EGRESS ACL L2/L3, TACACS+**, SSH v2/SSL, Mac based DHCP server, DHCP Option 82, DHCP server, IGMPv1/v2/v3/router port, QinQ are supported and also required in large network. It also supports Cisco Discovery Protocol (CDP) for Ciscoworks to detect the switch info and show on L2 map topology.

The highly flexible modular design consisting of maximum 24x Gigabit T+4xDual SFP,24x Giga PoE at/af (IPGS-5400-2P-PT)+4xDual SFP, 28xGigabit/100M SFP, 18x100M ST/SC + 4 Gigabit SFP covers the widest deployment of applications.

The built-in MMS server allows SCADA to control & monitor switch for data modeling.

Built-in MMS server for IEC61850 data modeling for monitoring and control
The built-in MMS (Manufacturing Messaging Specification) server can help SCADA to monitor and control switch by data modeling. It covers system, power, port status, network configuration.

Enhanced G.8032 ring, 16 MSTI MSTP; MRP ring
Lantech I(P)GS-5400-2P-PT features enhanced G.8032 ring which can be self-healed in less than 20ms for single ring topology protection covering Multicast packets. It also supports various ring topologies that covers double ring, multi-chain (under enhanced ring), train ring, basic ring, multiple-VLAN ring and auto-ring by easy setup than others. The innovative auto-Ring configurator (auto mode) can calculate owner and neighbor in one step. It supports MSTP that allows RSTP over VLAN for redundant links with 16 MSTI.

MRP (Media Redundancy Protocol) can be supported for industrial automation networks.

Miss-wiring avoidance, Loop protection, Node failure protection
The I(P)GS-5400-2P-PT also embedded several features for stronger and reliable network protection in an easy and intuitive way. When the pre-set ring configuration failed or looped by miss-wiring, Lantech I(P)GS-5400-2P-PT is able to alert with the LED indicator and disable ring automatically. Node failure protection ensures the switches in a ring to survive after power breakout is back. The status can be shown in NMS when each switch is back. This feature prevents the broken ring and keep ring alive without any re-configuration needed. Loop protection is also available to prevent the generation of broadcast storm when a dumb switch is inserted in a closed loop connection.

QoS by VLAN for legacy device
QoS by VLAN can allow switch to tag QoS by VLAN regardless the devices acknowledge QoS or not in which greatly enhance the bandwidth management in a network.

QinQ, QoS and GVRP supported
It supports the QinQ, QoS, GVRP for large VLAN segmentation.

802.1X security by MAC address
MAC-based port authentication is an alternative approach to 802.1x for authenticating hosts connected to a port. By authenticating based on the host's source MAC address, the host is not required to run a user for the 802.1x protocol. The RADIUS server that performs the authentication will inform the switch if this MAC can be registered in the MAC address table of switch.

IGMPv3,GMRP, router port, MLD Snooping, static multicast forwarding and multicast Ring protection
The unique multicast protection under enhanced G.8032 ring can offer immediate self-recovery instead of waiting for IGMP table timeout. It also supports IGMPv3, GMRP, router port, MLD snooping and static multicast forwarding binding by ports for video surveillance application.

Reliable network protection, node failure protection
The I(P)GS-5400-2P-PT also embedded several features for stronger and reliable network protection in an easy and intuitive way. When the pre-set ring configuration failed or looped by miss-wiring, Lantech I(P)GS-5400-2P-PT is able to alert with the LED indicator and send out an email or traps. Node failure protection ensures the switches in a ring to survive after power breakout is back. The status can be shown in NMS when each switch is back. This feature prevents the broken ring and keep ring alive without any re-configuration needed. Loop protection is also available to prevent the generation of broadcast storm when a dumb switch is inserted in a closed loop connection.

DHCP option 82 & Port based, Mac based DHCP, Option66, DHCP Snooping, IPv6 DHCP server
DHCP server can assign dedicated IP address by MAC or by port (Port based for single switch) , it also can assign IP address by port for multiple switches with single DHCP option82 server. DHCP Snooping is supported. For the ending device which need to download file from TFTP server, DHCP Option66 server can offer IP address of TFTP server to DHCP client. Basic IPv6 DHCP service can be supported.

User friendly GUI, Auto topology drawing
The user friendly UI, innovative auto topology drawing and topology demo makes I I(P)GS-5400-2P-PT much easier to get hands-on. The complete CLI enables professional engineer to configure setting by command line.

Editable configuration file
The configuration file of Lantech I(P)GS-5400-2P-PT can be exported and edited with word processor for the other switches configuration with ease. The factory reset button can restore the setting back to factory default. The built-in watchdog design can automatically reboot the switch when CPU is found dead.

Environmental monitoring for switch inside information
The environmental monitoring can detect switch overall temperature, total PoE load, voltage and current where can send the SNMP traps and email when abnormal.
The PoE modules support advanced PoE management including PoE detection and scheduling. PoE detection can detect if the connected PD is hang up then restart the PD; PoE scheduling is to allow pre-set power feeding schedule upon routine time table. It also supports per-port PoE status including current, voltage, watt and temperature information.

Event log & message; 2 DI + 2DO
In case of event, the I(P)GS-5400-2P-PT is able to send an email to pre-defined addresses as well as SNMP Traps out immediately. It provides 2DI and 2DO. When disconnection of the specific port was detected; DO will activate the signal LED to alarm. DI can integrate the sensors for events and DO will trigger the alarm while sending alert information to IP network with email and traps.

Various dual power conversions redundancy, high ESD protection
Lantech I(P)GS-5400-2P-PT chassis and modules are designed for easy maintenance and installation; It also supports dual power redundancies with isolated 85~264VAC/100~370VDC power conversion and isolated 36~75VDC power conversion or with non-isolated 12~56VDC power module to increase the network reliability. It also supports terminal block for connecting DC 48V PoE power source (IPGS-5400-2P-PT).

Lantech I(P)GS-5400-2P-PT features high reliability and robustness compliant with IEC-61850-3 & IEEE 1613 withstanding extensive EMI/RFI phenomenon, ±4kV surge, inductive load switching, high ESD (±8kV contact/ ±15kV air), 4kV EFT, high fault current environment usually found in Substation, Steel automation, Mining and Process control etc. IGS-5400-2P-E can run under operational temperature ranging from -40°C~75°C in the harsh and critical environment.

FEATURES

• System Interface/Performance
  • IEC-61850 & IEEE1613 Compliance
  • maximum 24x Gigabit T+4xSFP,24x Giga PoE at/af+4xSFP (IPGS-5400-2P), 28xGigabit/100M SFP, 18x100M ST/SC + 4 Gigabit SFP
  • 16K MAC Address Table
  • Backplane : 56Gbps
  • Dual isolated power conversions for 1600V DC(36V~75V)
  • Dual isolated power conversions for ±3000 V (85V~264VAC/100V~370VDC)
  • Dual power supply terinal block for non-isolated power DC(12V~56V)
  • Rear terminal block for PoE power source(DC48V) for IPGS-5400-2P-PT
  • Various modules available incl. Gigabit/100M SFP ; Gigabit T ;PoE at/af Giga T(up to 30W@) ; 100MST/SC modules
  • FAN less design
• MMS server built-in for SCADA monitoring/control
• 10KB jumbo frame supported on all ports
• User friendly UI, Auto topology drawing, topology demo
• IP v6/v4 supported
• Enhanced G.8032 Ring protection in 20ms < 256 switches
  • Support various ring/chain topologies, including train ring
  • Enhanced G.8032 ring configuration with ease
  • Auto ring configuration(auto mode) for single ring
  • Ring covers multicast on different ports
• DDM to support SFP diagnostic function***
  • Automatically convert the raw data into dB values for TX power/RX power, making it easier to measure the fiber distance
• 256 groups MSTP over VLAN
• VLAN
  • 4K 802.1Q Vlan, Port Based VLAN, GVRP, QinQ
• Port Trunk with LACP 14 trunks with automatic link failover
• LACP link aggregation to add bandwidth
• QoS (Quality of Service)
  • Supports IEEE 802.1p CoS
  • Per port provides 8 priority queues
  • Port-base,Tag-base and TOS Priority
  • Strict priority and WRR
• Security
  • SSL/SSH v2/ACL L2&L3
  • MAC address table: MAC address entries/Filter/MAC-Port binding
  • IP Security: IP address security management to prevent unauthorized intruder.
  • Management access control with priority
  • Login Security: IEEE802.1X/RADIUS
  • HTTPS for secure access to the web interface
  • TACACS+**
• Miss-wiring avoidance
  • LED indicator
  • Email or traps notification
• Node failure protection
  • Ensure the switches in a ring to survive after power breakout is back
  • The status can be shown in NMS when each switch is back
• SNTP,NTP supported
• IGMPv1,v2,v3 with Query mode for multimedia; GMRP
• IGMP router to select another Query mode and support IGMP static routing for reversed IGMP flow to bind with port for IP surveillance application
• Supports IEEE802.1ab LLDP, Cisco CDP
• DHCP server / client / DHCP Option 82 relay / DHCP Option 82 server; Port based DHCP server; DHCP Snooping; DHCP Option 66; basic IPv6 DHCP server
• Mac based DHCP server to assign IP address
• MLD Snooping for IPv6 Multicast stream
• Bandwidth Control
  • Ingress Packet Filter and Egress Rate Limit
  • Broadcast/Multicast Packet Filter Control
• System Event Log, Email alert and SNMP Trap for alarm support
• Diagnostic including Ping / DDM information
• Environmental sensor built-in to detect temperature, voltage, current and total PoE load(IPGS-5400-2P-PT) and send out SNMP traps and emails if there is abnormal events
• TFTP/FTP Firmware upgrade
• Reset / Factory default button to restore factory setting
• Watch dog design to reboot switch if CPU is found dead
• Provides 4kV EFT protection
• Provides ±8kV (Contact) and ±15kV (Air) ESD protection
• Provides ±4kV Surge protection
• 2 DI/DO and 1 relay contact alarm
• Support USB dongle for automatic backup / easily write configuration
• Auto Provision to verify switch firmware with the latest or certain version